11/17/2014

SANME Will Attend the Bauma China 2014

Bauma China will be held in Shanghai New International Expo Centre (SNIEC) from Nov. 25th to 28th 2014. There are many well-known construction machinery enterprises which all hoping to show at the event . Shanghai Sanme Mining Machinery Co., Ltd. will also attend the Bauma China 2014 with the latest products and technologies .

bauma china 2014


With more than 2700 exhibitors from 38 countries, 180,000 visitors from 141 countries, and 300,000 square meters of exhibition space, bauma China delivered impressive proof of its status as the biggest and most important sector event in Asia.
As the most advanced production systems Aggregates complete solution experts in China , Sanme has the most advanced technology and mature Sino-German joint venture turnkey solutions capabilities . In recent years, Sanme relies on the complete production process equipment capacity , successfully completed many large sand and gravel aggregate production line project , such as turnkey project for Lafarge, processing line of andesite for Holcim and so on. Regarding configuration of production line, SANME can always provide unique solution for every specific customer according the requirements of product and actual installation environment. So the service from SANME is much more high-end and individualized.

Booth information of SANME at Bauma China:
Time:from 25 to 28 in November, 2014
Address:Shanghai New International Expo Center(No. 2345, Longyang Road, Pudong New Area,Shanghai)
Booth No:E6.428
E-mail:sanme@sanmecrusher.com
Tel:+86-21-58205268

11/09/2014

Routine Maintenance Of the Cone Crusher

Any equipment will be wear and tear occurs with used for a long time, cone crusher is no exception. Because of non-stop work , cone crusher wear time and the material accumulated to a certain extent , there will be some equipment wear, may result in lower yields , or the material is not an ideal situation, then you need to replace the cone crusher accessories.

Therefore , when we use the cone crusher , to regularly carry out regular inspections of equipment, accessories , case can not be used due to cone crusher wear parts , resulting in a greater degree of damage to the machine .

Sanme remind you , cone crusher parts maintenance work is very important , can cause damage to some parts of the machine further damage , and may even unusable. For example, SMS multi-cylinder hydraulic cone crusher, hydraulic system damage if one component is not replaced in time , it may cause the entire hydraulic system is not working properly, it will affect production, but will also bring the loss of interest. In addition , such type of spring cone crusher and so on , but also do inspection, maintenance , especially after a period of time to look at the spring there is no need to replace the gasket .

Cone crusher crushing wall using new composite materials forged a cost-effective , super wear-resistant, wide applications and so on. After a new installation or a new replacement cone crusher wall work six to eight hours , you should check their retention , should be immediately found loose fastening , cone crusher to avoid unnecessary damage .

Cone crusher machine using the machine lies maintenance, so the machine will work for you longer , but your interest is to get the corresponding reward.

11/02/2014

best options for processing minerals

There are significant opportunities for the mining and processing of banded magnetite deposits on the African continent. A natural iron-ore deposit is a single deposit with little waste rock mixed into it. With massive iron-ore deposits, the head grade can be 60% to 70%, which means fewer impurities need to be removed before processing the ore into pig iron. The most massive ore bodies consist of hematite, which are the principal and the most stable of the iron oxides. The first step in the comminuting process and liberating a mineral from the ore body begins at the mining stage, with drilling or blasting and excavation used to generate materials that are easily transportable.

Crushers are then used to produce coarse size reduction and grinding mills are used to produce finer particles. As for the crushing process, Sanme crusher is a great option!

The ore mined from massive ore bodies is suitable for use in blast furnaces, they simply need to be crushed into pieces of between 10 mm and 25 mm, and then transported as lumpy ore to iron and steel plants worldwide. The ore is first crushed to size and then passed through a dense media separation process. The dense medium, with a specific gravity of around 3.6 t/m3, is created by mixing water with finely ground ferrosilicon powder. Anything with a specific gravity of less than 3.6 t/m3, for example silica-based rock, which has a density of 2.8 t/m3, will float, while the lumps of hematite iron-ore with a density of around 5.0 t/m3 will sink. What you see coming out of this process are big rocks floating in what looks like black water.

There are several kinds of comminution. In-pit comminution includes blasting, rock breaking and continuous mining; scrubbing, which is used as a polishing agent and not primarily for size reduction; crushing, which includes gyrators, jaw crushers, impactors and mineral screening; and grinding mills, which include the most commonly used semiautogenous grinding (SAG) mills, autogenously grinding (AG) mills, ball mills and rod mills..

10/26/2014

Crushed Aggregate for Construction

Crushed aggregate, also known as rock aggregate, refers to a crushed stone product produced in quarries. In areas where natural sand and gravel aggregate deposits are insufficient to handle local demand, larger stones are processed in an impact crusher to create crushed rock aggregate. The Upgraded Version HC Series Impact Crusher from Shanghai Sanme is a great choice for processing such kind of larger stones. The greater costs of production involved in mining and processing the stones to create crushed aggregate mean that the cost of this material is often significantly higher than that of comparable natural products.

All aggregate is divided into two types: fine and coarse. Fine crushed aggregate is broken up into smaller pieces than coarse crushed aggregate. When put through a separator or aggregate washer, coarse crushed aggregate will pass through a 3-inch (7.62-cm) sieve but will not go through a No. 4 sieve. Fine crushed aggregate will pass through a No. 4 sieve but will be stopped by a No. 200 sieve during the aggregate screening process.

The different aggregate sizes and types are appropriate for specific uses in the construction and landscaping industries. For example, although the larger, coarse crushed aggregates are more economical, this type of aggregate can present problems if used in concrete forms for upright structures. By comparison, fine aggregate is suitable for use in concrete, but it would not be a recommended choice for the creation of a roadbed or driveway.

10/21/2014

Best Methods for Disposing Construction Waste

There are two methods for disposing construction waste: stationary type and mobile type.

The complete mobile equipment for disposing construction waste includes mobile crushing plant and mobile screening equipment.

The complete stationary equipment for disposing construction waste includes crusher, screening equipment, magnetic separator and necessary transportation equipment.

Process: the construction waste can be divided into two parts by the primary screening equipment. The coarse material should be crushed again, then the magnetic separator help eliminate the lump metal material. Mobile crushing plant adopts professional separation process, for example, we can take the advantage of physical strength and or wet cleaning to make the useful material stay. Such kind of factory may be equipped with sorting device. Such as the bump vibrating equipment can classify and separate the light material such as wood, plastic and paper, etc, as well as the material with light pollution. The crushed material can be divided into inorganic combined aggregate with different purpose and different grain size. For instance, Germany processes the construction waste from the stationary construction waste recycling factory into inorganic aggregate with three level: 0-32mm, 0-45mm, 0-65mm according to the requirements of German standard DIN4226. It can offer the granulate aggregate used for special situation or for special requirements. such as O~8mm, 8~16mm, 16~32mm.

10/16/2014

How to Choose a Suitable Crusher

To choose a good and suitable crusher, you need to know what kind of materials you want to crush, size of materials and the output size of stones you want.

Jaw Crusher is widely used in mining, building materials, chemical industry, and metallurgy and so on. The Jaw Crusher is suitable for primary and secondary crushing all kinds of minerals and rocks with compressive strength less than 320 MPa. The biggest jaw crusher in China belongs to Shanghai Sanme. Its capacity is up to 1500TPH.JC series jaw crusher it is based on Sanme years' expertise in designing and conception and absorbs top crushing technology and research fruit in the world. It's birth thanks to finite element analysis method.

Impact Crusher is used for primary, secondary, fine crushing mining and rocks (for example, the granite, marble, and limestone) materials with compressive strength less than 350 MPa. The impact crusher is widely used for sand and rock producing in the industry of roads, railways, reservoir, electricity power and building materials and so on. As for impact crusher, Shanghai Sanme releases a latest upgraded version impact crusher: HC Series Impact Crusher, its capacity is up to 1200TPH.

The Spring Cone Crusher is widely used for secondary and fine crushing in the fields of mining, chemical industry, building materials, metallurgies and so on. The Cone Crusher can crush materials with Moh’s scale in middle and high hardness such as iron ore, copper ore, limestone, quartz, granite, rock and so on.

The Hammer Crusher is widely used in the industry of mining, building materials, chemical industry, metallurgies and fodder. The Hammer Crusher can secondary and fine crush materials in middle or less than middle hardness such as barite, limestone, terrazzo, silica sandstone, coal, coke, gypsum, aluminum sulfate, slag, etc.

10/12/2014

SANME Will Attend the 116th Canton Fair

SANME as a Sino-German JV Holding Group will attend the 116th Canton Fair 2014 from October 15th to 19th , 2014.

As a comprehensive international trade fair with the longest history, highest level, largest scale, complete range of goods and a large number of purchasers, Canton Fair has always been called the China’s foreign trade wind indicator. According to the official data, the accumulative export volume of the 115th Canton Fair in 2014 is 191.18 billion RMB (equivalent to USD 31.34 billion). SANME will present its latest research results to attract your attention during this fair, hoping to cooperate with new and old clients and do warmly welcome you pay a visit to our headquarters in Shanghai.

SANME’s Exhibition Information:

Name of exhibition: the 116th Canton Fair (China Import and Export Commodities Fair)

Duration: October 15th-19th, 2014

Address: Exhibition Hall for China Import and Export Commodities Fair (No.380 Yuejiang Zhong Road, Haizhu District, Guangzhou City)

Booth No.:1.1K20

Contact: Mr. Bruce

Mobile phone number: 0086-18017197802

Tel: (+86) 21-58205268

Fax: (+86)21-58200089

Email: sanme@sanmecrusher.com